Products & Solutions
Swan Swee supplies practical metal building products for hoarding, roofing, walling, structural support, and custom fabrication. Our range is built for site use, fast installation, and reliable performance across commercial, industrial, and infrastructure projects.
From coated steel sheets to purlins, flashing, and decking, we help contractors source the right material for the job from one supplier.
Materials & Finishes
The right finish does more than improve appearance. It helps protect the sheet against weather, corrosion, and daily site exposure. Swan Swee offers coating systems designed for different project needs, budgets, and environments.
Choose a finish based on the level of durability, colour retention, and corrosion resistance your project requires.
Hoarding
Our hoarding profiles are built for fast setup, dependable coverage, and practical site use. They are suitable for construction boundaries, temporary site enclosures, and project locations that need durable metal sheet solutions.
With different cover widths and profiles available, contractors can choose the right balance of speed, appearance, and handling for each site.
Profile
Sundek 760
Cover Width
760mm
Thickness Options
0.37 / 0.42 / 0.47 / 0.54mm
Rib Height
Standard
Usage
Hoarding, Roofing
Colours
8 standard
Profile
Cover Width
Thickness Options
Rib Height
Usage
Colours
Sundek 760
760mm
0.37 / 0.42 / 0.47 / 0.54mm
Standard
Hoarding, Roofing
8 standard
Sundek 1050
1050mm
0.37 / 0.47 / 0.54 / 0.64mm
Standard
Hoarding, Roofing
4 standard
Roofing & Walling
Swan Swee supplies roofing and walling profiles for projects that need reliable weather protection, practical installation, and clean finished lines. Our range covers standard exposed-fastener profiles, concealed-fix systems, and architectural roofing solutions.
Whether the requirement is cost efficiency, faster installation, lower-pitch performance, or a more premium finish, we offer profile options to match different project needs.
Profile
Sundek 760
Cover Width
760mm
Thickness
0.37–0.54mm
Min. Pitch
Standard
Fix Type
Exposed fastener
Best For
Standard roofing projects
Profile
Sundek 1050
Cover Width
1050mm
Thickness
0.37–0.64mm
Min. Pitch
Standard
Fix Type
Exposed fastener
Best For
Large areas, fast coverage
Profile
Swandek 920
Cover Width
920mm
Thickness
0.42–0.54mm
Min. Pitch
3°
Fix Type
Exposed fastener
Best For
Low-pitch, flexible design
Profile
Swift Seam
Cover Width
300–530mm
Thickness
0.55mm
Min. Pitch
3°
Fix Type
Concealed (mechanical seam)
Best For
Architectural, premium finish
Profile
Swift Lock
Cover Width
430mm
Thickness
0.54mm
Min. Pitch
Standard
Fix Type
Concealed (lock system)
Best For
Modern, screw-free installation
Profile
Cover Width
Thickness
Min. Pitch
Fix Type
Best For
Sundek 760
760mm
0.37–0.54mm
Standard
Exposed fastener
Standard roofing projects
Sundek 1050
1050mm
0.37–0.64mm
Standard
Exposed fastener
Large areas, fast coverage
Swandek 920
920mm
0.42–0.54mm
3°
Exposed fastener
Low-pitch, flexible design
Swift Seam
300–530mm
0.55mm
3°
Concealed (mechanical seam)
Architectural, premium finish
Swift Lock
430mm
0.54mm
Standard
Concealed (lock system)
Modern, screw-free installation
Roofing System
A complete roofing system is more than just the roof sheet. It includes the right profile, finish, support system, flashing, and detailing to help the roof perform properly over time.
Swan Swee supports roofing projects with coordinated materials for roofing sheets, purlins, flashings, and related components, helping contractors source the key parts from one supplier.
Flashing
Flashing helps complete the roof and wall system by covering joints, edges, ridges, corners, and transitions. It plays an important role in directing water away and improving the overall finish of the installation.a
Swan Swee provides common flashing types such as hip flashing, valley gutter, ridge-cap, corner-cap, and longitudinal flashing, with support for project-specific requirements.
- Hip Flashing — Used at the hip (sloped ridge) of a roof to cover and seal the junction where two sloping roof planes meet at an angle.
- Valley Gutter — Installed in the valley (internal angle) between two roof slopes. Channels rainwater runoff down and away from the junction.
- Ridge-Cap B — Covers and seals the ridge (top horizontal line) of a roof. Protects the peak from water ingress and gives a clean finished ridge line.
- Corner-Cap — Fitted at external wall or roof corners to protect the junction and provide a neat, weather-resistant finish at exposed corners.
- Longitudinal Flashing — Runs along the length of a roof or wall edge. Used at eave edges, parapet tops, or wall-to-roof transitions to seal the horizontal junction.
- Custom Flashing — Project-specific profiles are available. Contact our team with your requirements.
Structural Steel
Our structural steel range supports roofing, decking, framing, and general building works. It includes practical support products for projects that need strength, consistency, and ease of installation.
From steel decking to purlins and support sections, Swan Swee helps contractors source structural components that work with the wider building envelope system.
Product
Compdek
Function
Composite decking / formwork
Thickness
0.75mm / 1.00mm
Section / Width
600mm cover
Key Feature
G550 MPa, interlocking, permanent formwork
Product
C-Purlin
Function
Column, vertical & horizontal support
Thickness
1.5 / 1.9 / 2.4 / 3.0mm
Section / Width
75×45 to 300×96mm
Key Feature
Galvanised, high-tensile, wide size range
Product
Z-Purlin
Function
Roof truss & rafter support
Thickness
1.9 / 2.4 / 3.0mm
Section / Width
150×63 to 300×94mm
Key Feature
Z-shape allows overlap at supports
Product
Tophat
Function
Lightweight structural support
Thickness
0.75mm / 1.00mm
Section / Width
35×25×15mm
Key Feature
Economical, galvanised, reusable
Product
Function
Thickness
Section / Width
Key Feature
Compdek
Composite decking / formwork
0.75mm / 1.00mm
600mm cover
G550 MPa, interlocking, permanent formwork
C-Purlin
Column, vertical & horizontal support
1.5 / 1.9 / 2.4 / 3.0mm
75×45 to 300×96mm
Galvanised, high-tensile, wide size range
Z-Purlin
Roof truss & rafter support
1.9 / 2.4 / 3.0mm
150×63 to 300×94mm
Z-shape allows overlap at supports
Tophat
Lightweight structural support
0.75mm / 1.00mm
35×25×15mm
Economical, galvanised, reusable
Materials & Finishes
Color Max
ColorLume®
Hoarding
Sundek 760
Sundek 1050
Sundek 830
Sundek 700
Roofing & Walling
Sundek 760 (Roofing)
Sundek 1050 (Roofing)
Swandek 920
Swift Seam
Swift Lock
Roofing System
Flashing
Structural Steel
Compdek
Purlin
